The charcoal machine production line is a very popular charcoal production equipment in the machinery market. It can turn a lot of agricultural and forestry waste into waste, and the machine-made of charcoal is also a new energy source favored by the majority of users in the market. The charcoal machine production line It also points the way for China’s environmental protection machinery industry.
Many users know that the charcoal making machine product machine-made sells well and sells a lot, but it is not clear that the machine-made charcoal has a lot of uses in life. The following is a detailed introduction for everyone. The grill we usually eat, many of which are used in the charcoal machine to produce charcoal, extra clean, smokeless, and heat is still large, but the brush pot that is usually eaten is also the machine-made of charcoal.
The charcoal machine production line fills the raw materials containing biomass fibers that can produce charcoal, such as branches, straw, straw, peanut shells, trunks, cotton straw, tea seed husks, husks, weeds, leaves, etc., and pulverizes them into 10 mm by a pulverizer. The powder inside is dried by the dryer to make the moisture content within 12%. After being put into the rod machine through high temperature and high pressure, it is formed (without any additives) and then placed in a carbonization furnace for carbonization. charcoal. It is also possible to carbonize the material powder directly into a carbon powder using a continuous carbonization furnace.
Common faults and solutions for charcoal machine production line:
1. The rod making machine does not stick out. The reason is that the heating temperature is too high or too low, the forming sleeve of the rod making machine is worn more seriously, the angle of the screw propeller does not match, and the raw material moisture is too large. The charcoal making machine adopts the automatic temperature control device, and the forming sleeve is cast by high-alloy material, which is resistant to pressure and wear.
2, the salary bar does not form, the reason is improper temperature control, raw material moisture is too large, the rod machine propeller wear, the shaft tip is not correct, the vent hole is blocked, the rod machine propeller head spiral is too large or too small, the sleeve Serious wear and so on.
3. The quality of the salary bar is not high. If the moisture content of the raw material is too large, the rod body will be laterally cracked. If the moisture is too small, the longitudinal crack will easily occur. In addition, too high a heating temperature causes excessive softening of the raw material, which causes insufficient supply, which also causes cracks. Insufficient feeding of the feeding cylinder, the spiral diameter can be appropriately increased, or the spiral wall can be polished to increase the span between the spirals.
The raw materials used in the charcoal making machine on the production machine-made charcoal are all biomass waste, so it is favored by the majority of users, and the charcoal making machine cannot avoid failure during production, so the user should solve it in time, so that it can ensure its more Good production guarantees the production efficiency and effect of the charcoal machine production line.
Belt Type Continuous Charcoal Dryer Machine For BBQ Industry
This continuous charcoal dryer adopts advanced mesh belt heat transfer technology, which realises continuous and even hot air transfer and ensures that the charcoal gets the best effect during the whole drying process.
Wood Peeling Machine | Wood Log Debarker
Wood peeling machine is a professional equipment for removing the skin layer on the surface of wood, which is widely used in the fields of wood processing and pulp paper making.
BBQ Charcoal Production Line | Coal Ball Press Machine
BBQ charcoal production line is used to efficiently compress coal powder or wood chips, etc. into balls with uniform specifications and high density, aiming to improve efficiency and ensure the manufacture of high quality BBQ charcoal products.
Horizontal carbonization furnace | hardwood log charcoal machine
e horizontal carbonization furnace is a device that can carbonize raw materials. It is an essential machine in the process of coal production. It is widely used in charcoal processing plants because of its simple operation and high safety. There are many types of carbonization furnaces, including continuous carbonization furnaces and hoisting carbonization furnaces.
Comprehensive Crusher | Multi-functional Crushing Equipment
Large comprehensive crushers are generally used to process a wide range of various large sized stray timber and more. This article describes how its superior performance and comprehensive applicability make it ideal for wood processing.
Honeycomb Coal Briquette Production Line | Charcoal Forming Machine
The honeycomb coal briquette production line crushes, mixes, shapes and carbonises raw materials such as wood or straw, and finally produces highly efficient and environmentally friendly honeycomb coal products to meet a wide range of energy needs.